The Wavlink Aerial HS2 N200 Extender Setup includes a dual-band wifi range extender. The dead zone at your location is eliminated by using a high-power amplifier technique.
When set to its highest setting, the Wavlink Aerial HS2 N300 can reach speeds of up to 600 megabits per second. This page contains instructions for the Wavlink N300 and Wavlink Aerial HS2 extender.
Follow the steps that given below in order to setup your Wavlink HS2 Wifi Extender:
- Connect the Wavlink N300 Extender to an outlet first.
- The POE box’s Ethernet wire must be connected to the Aerial HS2 Extender.
- Use the same connection box to connect the second Ethernet cable to your primary router or modem.
- You can now connect any wirelessly capable device to the WAVLINK-N network.
- After connecting, open a web browser and navigate to wifi.wavlink.com.
- You’ve arrived at the N300 extender setup page.
- Use the default password “admin” to log in.
- Select “Router” and name your booster something catchy.
- Instead of none, change the security to WPA2-PSK (recommended). Next, enter your EXtender’s password and click “Next.”
- You have now successfully linked your Wavlink Aerial HS2 Extender Setup in router mode.
You can get in touch with us by calling our toll-free number or through live chat if you still need help with your Wavlink N300 Aerial HS2. We are always available to assist you and provide a solution.Now your Extender is ready for the new installation process.
How to install Wavlink Aerial HS2 Extender Setup in Repeater mode?
Repeater mode is one of the most straightforward modes for configuring your Wavlink Aerial HS2 Extender.
To finish your Wavlink Aerial HS2 Extender setup in repeater mode, follow these steps:
- A power supply must first be connected to the Aerial HS2 POE connector.
- Once the N300 has a solid green signal, connect the POE’s ethernet connection to the extender.
- Remove any wirelessly capable devices, such as laptops and phones, from the area.
- In addition, look for the WAVLINK-N network in the wireless settings menu.
- After connecting to the default network, launch a web browser that is compatible with Internet Explorer. Google Chrome, Mozilla Firefox, and Safari are the three options.
- Now enter ap.setup or 192.168.10.1.
- You’ve arrived at the Wavlink Aerial HS2 outside extender configuration page.
- Use the “admin” default password to log in.
- The extender has now been successfully configured to act as a repeater on your current WiFi network.
Keep in mind that you cannot connect any cables from the POE to the main router or modem if you want to use your extender as a repeater.
How to update Wavlink Aerial HS2 Extender firmware?
Firmware is made up of both hardware and software. The firmware is a set of software that is built into hardware. To resolve any issues (such as not providing the required speed or something else) that you may encounter while using your extender, you must update the firmware on your Aerial HS2. It includes additional security features as well as other new features that will assist you in resolving your issues.
Follow the steps below to update the firmware on your Wavlink Aerial HS2 Extender setup:
- Start your Wavlink Aerial HS2.
- Take out any mobile device.
- Enter ap.setup into the Search bar.
- Click on settings, then Firmware upgrade.
- To complete the firmware update operation, follow the instructions.
- It will take a minute; however, do not unplug the booster until the process is complete.
- Your Wavlink Aerial HS2 firmware upgrade is now successfully done.
How to reset my Wavlink Aerial HS2 Extender Setup?
If you have forgotten your admin password or username and would like to recover it. You must do a booster factory reset. It will remove all of your personal data, including passwords, usernames, and SSIDs, to prepare your extender for a new setup process. To complete the factory reset procedure, a hard pointed object, such as a paperclip or a needle, is required.
Follow the step given below for Wavlink Aerial HS2 Extender Reset process
- Connect the Wavlink N300 to a power outlet.
- Under a small hole, locate the factory reset button.
- It could be on the side panel of the repeater.
- Take the paper clip and hold it against the reset button for 8 to 10 seconds.
- It will restart automatically after a brief delay.
You can get in touch with us by calling our toll-free number or through live chat if you still need help with your Wavlink N300 Aerial HS2. We are always available to assist you and provide a solution.Now your Extender is ready for the new installation process.
Apart from this, if you want to know about How to update Wavlink Aerial HS2 Extender firmware? then please visit our Tech category